Samsung Washer SC Code Error? – Here Is How To Fix It Instantly

The washing machine drains the water by using a pressure switch that detects when the drum is full and the machine drains the water accordingly. When the drain does not start, the Samsung washer displays error code SC (5C), 5E, or ND. The E2 is found on older models (manufactured before 2007), where the E1 is found on newer models.

 

SAMSUNG WASHER SC ERROR CODE: DESCRIPTION.

As far as I know, there is no Samsung washer SC error code that exists. Many people confuse the number “5” with the English letter “S,” so they interpret the Samsung washer SC error code as 5C. Both combinations of symbols indicate a failure in the drainage system, so their meaning remains the same. In addition, problems can manifest themselves in a variety of ways:

  1. When the program is interrupted, there is water in the washing machine.
  2. The rate at which water leaves is too slow and too
  3. Despite the drum being empty, Samsung washer SC error code (5C) still appears on the display.

There is no way to rule out the possibility of the first two cases being external – the pipes may be clogged. Remove the hose from the faucet and place it in a large container so that the water can be drained. If the water is being pumped out, the drain or siphon under the sink needs to be cleaned.

The electronic controller may also be malfunctioning, sending/transmitting signals incorrectly. It is recommended that you turn off the washing machine after 10-15 minutes and repeat the process again.

 

REASONS FOR THE SAMSUNG WASHER SC ERROR CODE.

You need to figure out what kind of malfunction causes Samsung washer error code SC (5C) if restarting didn’t work. Be sure to drain the water from the drum and remove the laundry from the drum as soon as possible.

 

1. The pump filter of the washer is clogged.

Can you tell me if the pump is running but not pumping? The most crucial task you need to do is check the drain filter. Turn the counterclockwise plug with the pump filter out of the lower right corner of the door (on the front wall).

The draining process is not hindered too much by small items such as buttons, buttons, and coins. Samsung washer error code SC (5C) can only be caused by large obstacles, such as lint accumulations, clothing pieces, etc. Wash the filters and reinstall them after removing them.

 

2. There is a problem with the drain hose on the washer.

Verify the hose to make sure it is:

  • Freezing or clogging is not an issue.
  • Depending on its connection type, it is located correctly.
  • It is smooth and free of kinks or damage.
  • A maximum of 4 meters is allowed.

An incorrectly installed drain hose is the most common cause of stagnant water in a washing machine. In order to comply with the manufacturer’s instructions, it should be attached. It is also a good idea to check if there is anything extra inside the bag at the same time. Under the pressure of air, liquid, or manual pressure, obstructions can be removed.

 

3. Foreign objects in the pipe of the washer.

It is not uncommon for a blockage to form in the drain pipe. A Samsung washer SC error code (5C) appears on the display when the technician does not pump out the water. The connection between the pump and the tank should be kept free of debris. Whenever a passage is clogged, it must be unclogged in order for it to function properly.

 

4. There is a blockage in the pump of the washer.

Small objects such as coins, nails, screws, hair clips, or rubber bands may cause continuous/intermittent pump noise. It is important to know that a quiet hum indicates that the node is working, but it is jammed. Turn on the drain mode, remove the filter, and watch the impeller turn as the drain mode is turned on. Make sure there are no hidden obstructions in the pump outlet chamber or under the impeller. When inspecting the pump filter, this step is usually performed immediately.

 

5. Washer wire connection is loose.

It is quite another matter if the pump does not make any sounds at all. An open contact on the electrical circuit may be the cause of the Samsung washer SC error code (5C). Ensure that the drain pump’s wires are connected to the control module. If they have come off, it is likely that they need to be fixed and that they will need to be replaced. It is common for this to happen after the washing machine has been moved or transported.

A malfunction may also be caused by damaged wiring, which is another likely cause of a malfunction. Depending on the situation, take the following actions:

  • By twisting, you can restore the open circuit if the defects are minor.
  • Replace the loop completely if everything is serious.

 

6. The pump of the washer broke down.

Samsung washer error code SC (5C) appears when the washing machine does not spin, does not drain, and does not drain water. 90% of the time, faulty pumping systems are the root cause of the problem. It is imperative to realize that a broken pump does not necessarily have to be silent. Despite the fact that the rotor is able to rotate at normal speed, the impeller cannot move. During draining, Samsung washer error code SC is displayed due to slippage on the shaft.

What is the most dependable way to check the pump?

  1. To access the contacts, turn the washing machine on its side.
  2. The front cover and control panel should be removed.
  3. Make sure the electrical circuit at the terminals is continuous by using a multimeter. There is a typical resistance of 165 ohms in the pump windings. However, the pump resistance may vary between washing machine models.
  4. Call a specialist if the Samsung washer SC (5C) error code continues to appear even after everything is in order.

When the pump fails, it will have to be replaced, and the average cost is around $20.

 

7. There is a blockage or malfunction of the pressure switch of the washer.

In the event of such a blockage, the washing machine displays the SC error code (5C) as a signal of stagnant water. Due to a blockage in the pressure system, incorrect signals are sent to the control board when the washing machine is drained. Due to the misconception that the car is still full, it does not start spinning rapidly.

The pressure switch should be cleaned as follows:

  1. Disconnect the equipment from the power source.
  2. The panel should be removed.
  3. The rubber tube on the pressure switch should be unscrewed.
  4. It should be blown gently.

When the drum is empty and no air passes through, dirt or limescale has accumulated.

The SC (5C) error can also be triggered by a malfunctioning water level sensor. The Samsung washer error code 1E, for example, is a different error code for this sensor.

 

8. There’s a problem with the washer’s control module.

It cannot send signals to the pump motor if the microcircuit is out of order. Due to this, the pump will not be in a position to pump out any water. There should be a repair or a complete replacement of the board. A washing machine’s pump is one of the most expensive parts of the machine. The cost of repairing an item is often higher than the cost of replacing it. However, it all depends on the person who is going to do the repair.

 

Is there a reason why my Samsung washer shows a SC code?

The SC error code signifies that there is an issue with the drain. Although the pump is running, the amount of water in the drum does not decrease. Blockages may occur in pipes, filters, drain hoses, pipes, or pumps. A malfunctioning pump, pressure switch, or control module can also cause this problem.

 

Why does Samsung have SC error code in its washing machine?

The SC error occurs when the washing machine is powerless to drain the water. In case the water level in the drum doesn’t decrease, the mainboard interrupts the cycle. There may be a clog in the drainage system that is interfering with the drainage process. Also possible are technical malfunctions, such as damage to wires, hoses, pressure switches, engine breakdowns, or impeller problems.

 

Is there a way to fix the Samsung washer SC error code?

In the event that SC error occurs when the drum is empty, it is recommended that the pressure switch be replaced. Inspect the drainage system if there is water in the washing machine. Check the pump and its leads for any clogged hoses, nozzles, filters, or impellers.

 

Read More:

Leave a Reply

Your email address will not be published. Required fields are marked *