Whirlpool washers are designed to properly agitate and clean loads, but it’s just as important that they drain the water used to clean your load. Is it possible to figure out why your Whirlpool washer suddenly won’t drain, and what can you do to resolve this not draining issue?

The reason why your Whirlpool washer won’t drain may be triggered by clogged drain pumps, kinked drain hoses, or faulty lid switches. The problem can be resolved by partially disassembling your washer on your own and unclogging or replacing any problematic parts.

Many people forget how important it is to be able to wash items without thinking twice, until their washer suddenly fails. You should drain all of the water from your Whirlpool washer’s drum at the end of every cycle. By spinning the clothes, excess water is removed and the clothes can dry properly after washing. Here are some reasons why your Whirlpool washer won’t drain, and how you can fix it.

The truth is that there are quite a bit of causes why a Whirlpool Washer Won’t Drain.

If you were to open the lid or door of your Whirlpool washer mid-cycle, you would notice a large amount of water submerging your laundry items. With agitation motions, this water works with your detergent to remove all the dirt and grime from your clothes. If your washer does not drain the dirty water immediately after this process, what should you do?

It is possible that the clogged pump in your Whirlpool washer could be the reason your washer won’t drain. As a result of small items falling out of clothing, your washer can hold water due to a clogged drain. Ensure your washing machine’s drain pump is not obstructed by any objects by removing it.

Be sure to carefully remove any objects that are obstructing your Whirlpool washer’s drain pump after removing the drain pump. The pump should not be obstructed if nothing is blocking it. However, if the drain looks very worn, it may merely be a matter of replacing the drain pump. Your washer will drain more effectively at the end of the cycle if you have a newer pump.

Whirlpool Washer Won’t Drain To The Fullest.

If you have set the load size for that particular load while the washer is in the middle of the cycle. There will be a slight, midway, or full fill of water in the washer. All items should be completely submerged in water, so that the tops are covered with water. Water should drain completely without a trace, not only partially, regardless of the size of the load.

If your Whirlpool washer won’t drain completely, look at the drain hose for kinks or bends. It is also possible for the drain hose to become obstructed with small items, just like the drain pump. This can cause your washer to drain partially rather than completely.

Make sure your drain hose is free of kinks and bends once you have reached it. Make sure neither of these has caused wear or tears within the hose itself if you see them. You should also make sure the drain hose isn’t higher than 96 inches off the floor, as if it’s too high, it won’t drain. Since gravity cannot work well enough to drain the washer properly, water will remain in the drum.

A clog has been detected in the Whirlpool washer drain.

Technology inside many Whirlpool washers makes it possible to detect what is wrong without you having to investigate on your own. Whirlpool’s features include alerting you when a drain clog is detected. You may wonder if a repairman is needed if you receive this message. However, take a look at the instructions below for a possible solution to Whielpool washer won’t drain properly.

Whenever your Whirlpool washer senses a clog, disconnect it and raise it from the front, placing two-by-four blocks under each foot. The drain pump can be accessed by unscrewing three screws at the base of the panel.

Remove the drain pump’s knob with a Phillips screwdriver while holding a bucket underneath to catch any excess water. Once the knob has been turned over, you will see the filter on the back. Plug the pump back in, replace the drain filter, screw on the cover, and remove the blocks.

Is It Possible to Resolve a Whirlpool Washer That Is Not Draining?

When your Whirlpool washer stops draining and you can no longer get your clothes dry, you are left with a lot of wet clothes. But if you don’t want to immediately call a repairman, you’re also left with the task of fixing it yourself. You can fix your own appliances with the right tools and instructions, despite the fact that it may seem daunting. Find out how to resolve a Whirlpool washer that is not draining by reading below.

It may be that the lid switch assembly is malfunctioning on a Whirlpool washer that is not draining. The control panel can be removed by unplugging the washer and removing two screws. Locate the case with three wires under the control panel and unplug it. A continuity test can be carried out with an ohmmeter.

It is necessary to replace the lid switch if there is no continuity between the two outside wires on the female plug end. The wires should be removed from the case by removing the two clips on each side. In order to drain your washer, you will need to install a new lid switch and attach the wires to it.

Is There An Other Method That You Can Try If Your Whirlpool Washer Won’t Drain?

When it comes to washing machines, it can be very difficult to decide how to solve a problem if one arises. When you make a mistake, you could end up with water at your feet rather than in the drum. The owner of the washer can, however, repair it themselves without having to hire a professional. It is imperative to know what to do before tackling the challenge.

Symptoms of a Whirlpool washer that won’t drain include a clogged drain pump, a kinked drain hose, or a broken lid switch assembly. Check out the previous sections for step-by-step troubleshooting guides for each of these issues.

A coin trap that is too full in your washer is a less likely problem, but it sometimes causes problems. In some Whirlpool washer models, a small access door is located at the lower front of the washer. See if draining happens more easily and more completely if you open the access door and remove anything you find inside the coin trap.

Read More: